HB-2 high-velocity correlation model at high angles of attack in supersonic wind tunnel tests

Responding to a need for experimental data on a standard wind tunnel model at high angles of attack in the supersonic speed range, and in the absence of suitable reference data, a series of tests of two HB-2 standard models of different sizes was performed in the T-38 trisonic wind tunnel of Vojnotehnickˇi Institut(VTI), in the Mach number range 1.5–4.0, at angles of attack up to+30°. Tests were performed at relatively high Reynolds numbers of 2.2 millions to 4.5 millions(based on model forebody diameter). Results were compared with available low angle of attack data from other facilities, and, as a good agreement was found, it was assumed that, by implication, the obtained high angle of attack results were valid as well. Therefore, the results can be used as a reference database for the HB-2 model at high angles of attack in the supersonic speed range, which was not available before. The results are presented in comparison with available reference data, but also contain data for some Mach numbers not given in other publications.     

Evaluation and improvement of coastal GNSS reflectometry sea level variations from existing GNSS stations in Taiwan

Global sea level rise due to an increasingly warmer climate has begun to induce hazards, adversely affecting the lives and properties of people residing in low-lying coastal regions and islands. Therefore, it is important to monitor and understand variations in coastal sea level covering offshore regions. Signal-to-noise ratio (SNR) data of Global Navigation Satellite System (GNSS) have been successfully used to robustly derive sea level heights (SLHs). In Taiwan, there are a number of continuously operating GNSS stations, not originally installed for sea level monitoring. They were established in harbors or near coastal regions for monitoring land motion. This study utilizes existing SNR data from three GNSS stations (Kaohsiung, Suao, and TaiCOAST) in Taiwan to compute SLHs with two methods, namely, Lomb–Scargle Periodogram (LSP)-only, and LSP aided with tidal harmonic analysis developed in this study. The results of both methods are compared with co-located or nearby tide gauge records. Due to the poor quality of SNR data, the worst accuracy of SLHs derived from traditional LSP-only method exceeds 1?m at the TaiCOAST station. With our procedure, the standard deviations (STDs) of difference between GNSS-derived SLHs and tide gauge records in Kaohsiung and Suao stations decreased to 10?cm and the results show excellent agreement with tide gauge derived relative sea level records, with STD of differences of 7?cm and correlation coefficient of 0.96. In addition, the absolute GNSS-R sea level trend in Kaohsiung during 2006–2011 agrees well with that derived from satellite altimetry. We conclude that the coastal GNSS stations in Taiwan have the potential of monitoring absolute coastal sea level change accurately when our proposed methodology is used.     

盖板式预旋系统的压比和熵增特性

对预旋系统内的压力变化相关研究较少。基于理论分析、实验测量以及数值计算,对某盖板式预旋系统的压比及熵增特性进行研究。通过理论推导,对预旋系统内压比与无量纲温降的关系进行分析。在最高转速可达10000r/min的高转速实验台上,测量了转盘上的气流静压以及相对总温,进而获得压比及熵增特性。进行三维数值计算,将数值计算结果与实验结果进行了对比,并根据数值计算结果对预旋系统内的熵产分布以及各元件的熵增情况进行分析。结果表明:系统温降以及旋转马赫数大小决定了预旋系统的理想最大压比,而实际压比与理想压比的比值取决于系统内的熵增大小。采用数值计算以及实验测量所得结果对理论关系式进行了验证,最大偏差2.7%。旋转马赫数一定的条件下,随系统无量纲温降增大,系统压比逐渐减小。由于熵增影响,实测压比与理想压比最大相差约36%。预旋系统内的熵增主要发生在预旋腔静止壁面、接受孔前后、供给孔进口等气流旋转比发生剧烈变化的区域。预旋系统内主要元件的熵增随流量增大都呈逐渐增大的趋势,但接受孔处熵增最小值出现在喷嘴出口旋转比等于1左右时,流量过小或过大都会导致接受孔处熵增变大。     

大厚度比零件（外侧）和波纹管（内侧）的缝焊研究

某重点型号波纹管组合件的设计要求是缝焊，对照以往产品的结构，比较明显的情况是波纹管在零件的内侧。零件的厚度是3mm，波纹管的厚度是0.1mm，零件与波纹管的厚度比比较大。波纹管在零件的内侧会产生一个问题：波纹管在焊接过程中会逐渐收缩，到最后与零件之间产生间隙，导致局部形不成焊缝。研究通过减小车配间隙,增加冷却手段、滚轮厚度和压力等措施来实现大厚度比的零件和波纹管之间的缝焊。     

飞机变形自动化测量方法研究

为解决以往飞机变形测量模式中人工干预较多,受测量环境影响较大,测量时间长等问题,基于Geo COM技术和RS232,在计算机与全站仪之间进行数据交换,设计了一套自动化测量系统。在测量过程中由标志点的机体理论坐标反算其在当前测站中的极坐标,从而在测量过程中驱动全站仪指向待测点,减少人工瞄准时间,并由计算机实时解算结果数据。经实际飞行试验验证表明,测量时间缩短为原来时间一半,大大提高了工作效率。     

微流量测量方法及其技术的发展

归纳了近五年来基于MEMS技术的微流量传感器结构及性能参数。根据国际上热门的研究方法推断微流量测量技术可能的发展方向与研究趋势,即集成两种或两种以上的测量方法,实现优势互补,提高测量精度或扩大量程比。最后基于现有的技术基础,提出了融合科氏效应与差压效应的微流量测量方法,阐述了传感器的工作原理与理论基础,并对其可行性进行了分析与论证。     

基于压力信号分析的轴流式压气机失速预测

为了得到压气机工作状态的稳定观测点,并建立压气机近喘失速工作状态与压气机压力信号的相关关系,本文针对低速双级轴流式压气机,分别进行了均匀进气及畸变进气条件下不同转速的近喘失速试验,实时动态测量标定压气机由正常工作到失速工况下压力信号,并在时域内提出了一种基于自相关系数的压气机失速预测算法,对进口、出口以及压气机首级转子叶尖位置压力信号预测分析。结果表明所提出的预测算法具有良好的失速预测能力,且发现叶尖处离叶片前缘20%的位置,最适宜作为压气机失速预测的观测点,此时压气机叶尖压力自相关性数据与压气机喘振裕度具有明显的单调相关性。     

复杂凸凹曲率飞机蒙皮充液成形技术研究与应用

随着飞机气动、隐身等性能要求的提高,飞机外形曲率更加异形化,大量应用复杂凸凹曲率蒙皮,传统的拉伸成形方法已经不能完全满足新一代飞机蒙皮加工的要求。基于生产某型号飞机复杂凸凹曲率蒙皮这一背景,介绍了充液成形基本原理及关键技术,利用有限元数值模拟方法,分析板材充液成形过程中液室压力、厚度减薄率、板材失稳及贴胎度的变化规律,优化工艺参数,并且根据数值模拟结果指导工业生产。理论分析和现场实践证明:充液成形技术为复杂凸凹曲率蒙皮零件的制造提供了新的工艺方法,满足新一代飞机的凸凹曲率外形蒙皮的制造要求。     

GAP/CL-20高能固体推进剂燃烧性能影响因素

采用水下声发射法测试了推进剂静态燃速,用线性回归法计算了推进剂燃速压强指数;研究了GAP/CL-20高能固体推进剂中增塑比及固体组分AP、CL-20、Al粉粒度等配方组成因素对燃烧性能的影响。研究结果表明,增塑比一定范围内的变化不会对推进剂燃烧性能产生显著影响,其燃速和燃速压强指数基本不变;CL-20粒度减小或AP粒度增加均会导致燃速不同程度的降低,Al粒度减小也会使燃速减小,但在达到一定程度后,燃速又增加;推进剂燃速压强指数随CL-20、Al粉粒度减小和AP粒度增加而减小,并对其燃烧性能的影响机制进行了简单分析。     

超高速撞击下PTFE/Al含能材料薄板的载荷特性分析

不同于传统惰性材料的空间碎片防护结构,含能材料防护结构在超高速撞击下的冲击起爆特性是其防护能力得以提高的根本原因。PTFE/Al含能材料防护结构的冲击起爆特性改变了弹丸强冲击载荷下的破碎机制,弹丸内部的冲击压力对于分析含能材料在超高速撞击下的防护机理具有重要意义。对超高速撞击试验中回收的PTFE/Al防护结构后板进行损伤特性分析,获得了对应速度条件下弹丸的破碎特性。基于一维冲击波理论,分析PTFE/Al靶板在超高速撞击条件下的冲击响应过程,结合考虑化学反应效率的热化学反应模型,获得了弹丸在碰撞与爆炸联合作用下的载荷特性,通过与试验结果对比验证,获得该材料完全反应的临界撞击速度约为1800 m/s,弹丸的临界破碎速度为2875 m/s,小于铝防护结构中对应的临界破碎速度。给出了弹丸在PTFE/Al、铝两种防护结构中产生相同冲击压力时对应的临界速度,分别为弹道段的800 m/s和破碎段的3580 m/s。